The 2 RU four channel D80 amplifier is a high power density amplifier, ideally suited for use in both mobile and installation environments. It contains configurations for all d&b loudspeakers and a linear mode. The signal delay capability enables user definable settings of up to 10 s (= 3440 m/11286 ft) to be applied independently to each channel. The same applies to the two 16-band equalizers, providing optional parametric, asymmetric, shelving or notch filtering. The D80 incorporates a colour TFT touchscreen, offering quick access to the menu structure, while the rotary encoder can be used for fine adjustment. The front panel and the integrated touchscreen of the D80 amplifier is tilted up for ease of operation when the amplifier is below eye level. The equal ratio of signal input to amplifier output channels increases the application flexibility particularly for monitor, frontfill or effect channel use. The LoadMatch function integrated within the D80 amplifier enables the electrical compensation of loudspeaker cable properties, without the need for an extra conductor. This results in an increased accuracy of audio reproduction over a bandwidth of up to 20 kHz, preserving the tonal balance when cable lengths of up to 70 m (230 ft) are used. The D80 incorporates Class D amplifiers utilizing a power supply with active Power Factor Correction (PFC) suitable for mains voltages 100 V/120 V/200 V/230 V, 50 - 60 Hz and maintains a stable output when used with weak or unstable mains supplies. An NL8 provides all outputs on a single connector, while individual outputs are optionally NL4 or EP5 connectors. RJ 45 and etherCON connectors enable access to the d&b Remote network via CAN-Bus and OCA/AES70 via Ethernet respectively.
-
The 2 RU two channel lightweight D6 amplifier delivers medium power into low impedance loads between 4 and 16 ohms and is ideally suited for use in both mobile and installation environments. The D6 contains configurations for d&b loudspeakers and a linear mode; exceptions are 2-Way Active, V-Series and B2-SUB. The signal delay capability enables user definable settings of up to 340 msec (=100 m/328.1 ft) to be applied independently to each channel. The same applies to the 4-band parametric equalizer, providing optional boost/cut or notch filtering. The D6 incorporates a digital rotary encoder and a LCD display to configure the amplifier. The D6 incorporates Class D amplifiers utilizing a switch mode power supply with active Power Factor Correction (PFC), suitable for mains voltages 100 V/120 V/200 V/ 230 V, 50 - 60 Hz and maintains a stable and increased output when used with weak or unstable mains supplies. It is supplied with two NL4 loudspeaker output connectors. RJ 45 connectors enable access to the Remote network via CAN-Bus. d&b System check verifies that the system performs within a predefined condition, whilst d&b Load monitoring enables an automatic and continuous impedance monitoring. Both can determine the status of an LF or HF driver in systems with multiple elements, even if these are crossed over passively.
-
The 2 RU four channel D20 amplifier is ideally suited to mobile and installation applications which require low to medium Sound Pressure Level (SPL) capabilities. The D20 features the same Digital Signal Processing (DSP) platform as the latest generation of d&b amplifiers, containing configurations for all d&b loudspeakers except the J-Series and the M2 monitor, plus a linear mode. The signal delay capability enables user definable settings of up to 10 s (= 3440 m/11286 ft), which can be applied independently to each channel. The same applies to the two 16-band equalizers, providing optional parametric, asymmetric, shelving or notch filtering. The D20 incorporates a colour TFT touchscreen, offering quick access to the menu structure, while the rotary encoder can be used for fine adjustment. The front panel and the integrated touchscreen are tilted up for easy operation when the amplifier is below eye level. The equal ratio of signal input to amplifier output channels increases application flexibility particularly for monitor, frontfill or effect channel use. The LoadMatch function integrated within the D20 amplifier electrically compensates for the properties of loudspeaker cable used. The D20 incorporates Class D amplifiers utilizing a power supply with active Power Factor Correction (PFC) suitable for mains voltages 100 V - 240 V, 50 - 60 Hz and maintains a stable output when used with weak or unstable mains supplies. An NL8 provides all outputs on a single connector for loudspeaker multicores. Dual channel mode is driven through four individual NL4 connectors, while Mix TOP/SUB and 2-Way Active mode output configurations for applicable d&b loudspeakers are available via two central NL4 connectors. etherCON and RJ 45 connectors enable access to the d&b Remote network through OCA/AES70 via Ethernet and through CAN-Bus respectively.
-
The 3 RU two channel D12 amplifier delivers medium to high power into low impedance loads between 4 and 16 ohms and is ideally suited for use in both mobile and installation environments. The D12 contains setups for all d&b loudspeakers and a linear mode. The signal delay capability enables user definable settings of up to 340 msec (=100 m/328.1 ft) to be applied independently to each channel. The same applies to the 4-band parametric equalizer, providing optional boost/cut or notch filtering. The D12 incorporates a digital rotary encoder and a LCD display to configure the amplifier. The D12 utilizes an autosensing switch mode power supply for mains voltages 120 V/230 V, 50 - 60 Hz (optional 100/200V). The D12 amplifier incorporates d&b SenseDrive for accurate control of LF drivers in d&b loudspeakers driven in 2-Way Active mode or in actively driven d&b subwoofers. When the D12 is fitted with EP5 connectors and appropriate 5 wire cabling, d&b SenseDrive can be used, resulting in an extremely precise bass performance even at high levels. NL4 and NL8 connector options are also available. RJ 45 connectors enable access to the Remote network via CAN-Bus. d&b System check verifies that the system performs within a predefined condition, whilst d&b Load monitoring enables an automatic and continuous impedance monitoring. Both can determine the status of an LF or HF driver in systems with multiple elements, even if these are crossed over passively.
-
J-SUB is a bi-amplified 2-way bass-reflex subwoofer incorporating three 18 "long-excursion neodymium speakers, two of which are mounted on the front panel and one on the rear panel. which derives from this architecture avoids the unwanted projection of energy behind the system, which thus benefits from a considerable reduction of the reverberated field at the serious frequencies and therefore translates into an incomparable reproduction precision.The J-SUB systems can be used to complement the J8 and J12 systems in various combinations, either on the ground or suspended, either integrated into the column at the top of the J8 / J12 array, or in independent J-SUB columns. built in marine plywood covered with the exclusive PCP (Polyurea Cabinet Protection) treatment to protect against shocks and atmospheric agents.The front and back panels are protected by a rigid metal grid ca, while on each side panel there are four handles. Four 100mm wheels and an EP5 or NL8 connector complete the rear panel.
-
The 3 RU two channel D12 amplifier delivers medium to high power into low impedance loads between 4 and 16 ohms and is ideally suited for use in both mobile and installation environments. The D12 contains setups for all d&b loudspeakers and a linear mode. The signal delay capability enables user definable settings of up to 340 msec (=100 m/328.1 ft) to be applied independently to each channel. The same applies to the 4-band parametric equalizer, providing optional boost/cut or notch filtering. The D12 incorporates a digital rotary encoder and a LCD display to configure the amplifier.
-
Rental Audio kit d & b audiotechnik composed by: N.6 d & b Q1 N.2 d & b Q7 No. 6 d & b QSub N.4 d & b D12 N.1 Yamaha LS9 mixer Design and configuration assistance -
BEHRINGER B-CONTROL FADER BCF2000: Total-Recall USB/MIDI Controller with 8 Motorized Faders. Total-recall, cascadable desktop MIDI controller with analog feel and intuitive user interface. 8 ultra-precise, 100-mm, motorized faders for ultimate control of virtual mixers, organ-drawbars (inverse mode) or virtual synths and samplers. 4 virtual groups with 8 dual-mode, high-resolution encoders that feature LED rings and an additional push function. 16 + 4 illuminated buttons freely assignable to all types of MIDI functions from note on/off, control change and program change to MMC and system exclusive data. All panel elements freely assignable - manually or via user-friendly learn mode. Additional multi-function foot switch and foot controller connectors can be used to address all types of MIDI data. 32 user presets each with 4 encoder groups. Configurable MIDI and USB modes for ultra-flexible system integration. 1 MIDI In plus 2 MIDI Outs, usable as an additional USB to MIDI interface. Multi-function, 4-digit LED display with real-time parameter indication plus write-in fields for your own labeling. MIDI input with merge function for cascading several control units. Easy connection to any computer/expander, etc. using standard MIDI In/Out connectors. Generic USB MIDI support with Windows XP and Mac OS X operating systems. Additional drivers and editor/librarian software available for free download at behringer.com. High-quality components and exceptionally rugged construction ensure long life. Conceived and designed by BEHRINGER Germany. Redefine how you make music. Be in control with the BCF2000! Stop by your local BEHRINGER dealer and push those faders around.
-
The versatile gooseneck provides stable and repeatable positioning. The mics can be easily unclipped and repositioned or moved to another instrument. The mounting system is designed to never blemish or scratch the finish of your instrument. The flexible design supports a wide variety of mounting and positioning possibilities.
-
Clip for attaching a 4099 instrument microphone to thin-bodied and unusually shaped instruments. The design of the microphone clip includes a Velcro attachment strap to fit instruments of various sizes and diameters such as oboe, clarinet, bassoon, recorder and flute. The attachment strap tightens to fit the circumference of the instrument, like a wristwatch on your arm
-
The versatile gooseneck provides stable and repeatable positioning. The mics can be easily unclipped and repositioned or moved to another instrument. The mounting system is designed to never blemish or scratch your instrument. And you can use any mute together with the microphone clip. It is also easy to place your instrument in a stand with the mic and clip on.
-
The versatile magnet mount/gooseneck system provides stable and repeatable positioning.The mics can easily be positioned at different angles to provide a variety of sound nuances. The mounting system is designed to never blemish or scratch the finish of your instrument. The flexible design supports a wide variety of mounting and positioning possibilities.
The mount can also be used with various instruments with magnetic surfaces.