Rent Audio Equipment

Professional Audio Equipment rental for any conference, convention and high quality corporate event

  • Sennheiser EM 6000 is a two-channel digital receiver and operates over a bandwidth of 244 MHz (470-714 MHz) that is covered by the three transmitter versions (470-558 MHz, 550-638 MHz, and 630-718 MHz). For multichannel systems, up to eight receivers can be cascaded without the need for an additional antenna splitter since it is built into the receiver itself; the multichannel system then operates with a single pair of antennas. System latency is 3 milliseconds. Superior reception, reliable audio Reliability has always been a hallmark of Sennheiser wireless systems, and Digital 6000 fulfills this promise by employing true bit diversity, transmission error correction, and additional intelligent error concealment. True bit diversity ensures significantly better reception quality than is available with other systems. While diversity or true diversity use the RF signal from a single antenna or the audio signal from a single receive path, respectively, true bit diversity uses both receive circuits and combines their information to create the optimum receive signal in this way. Digital 6000 receivers are equipped with a Link Quality Indicator that ensures that problems are seen before signal losses arise. If, as is the case in difficult RF environments, the signal was momentarily degraded to such an extent that transmission error correction could not perform any repair, the Digital 6000's intelligent error concealment is activated. By employing intelligent learning algorithms to replace the deteriorated signal, the Digital 6000 still transmits perfectly where other digital systems might fail. For data security, an especially important feature for conferencing and business use, Digital 6000 enables AES 256 encryption. The EM 6000 receiver features an easy-to-view white OLED display that provides a quick overview of the RF signal, link quality, audio signal, battery status, frequency and encryption. Several screens provide easy access to additional information without the user having to search through complicated sub-menus. Messages of critical operating and error conditions are shown directly on the display.
  • Sennheiser EM 6000 is a two-channel digital receiver and operates over a bandwidth of 244 MHz (470-714 MHz) that is covered by the three transmitter versions (470-558 MHz, 550-638 MHz, and 630-718 MHz). For multichannel systems, up to eight receivers can be cascaded without the need for an additional antenna splitter since it is built into the receiver itself; the multichannel system then operates with a single pair of antennas. System latency is 3 milliseconds. Superior reception, reliable audio Reliability has always been a hallmark of Sennheiser wireless systems, and Digital 6000 fulfills this promise by employing true bit diversity, transmission error correction, and additional intelligent error concealment. True bit diversity ensures significantly better reception quality than is available with other systems. While diversity or true diversity use the RF signal from a single antenna or the audio signal from a single receive path, respectively, true bit diversity uses both receive circuits and combines their information to create the optimum receive signal in this way. Digital 6000 receivers are equipped with a Link Quality Indicator that ensures that problems are seen before signal losses arise. If, as is the case in difficult RF environments, the signal was momentarily degraded to such an extent that transmission error correction could not perform any repair, the Digital 6000's intelligent error concealment is activated. By employing intelligent learning algorithms to replace the deteriorated signal, the Digital 6000 still transmits perfectly where other digital systems might fail. For data security, an especially important feature for conferencing and business use, Digital 6000 enables AES 256 encryption. The EM 6000 receiver features an easy-to-view white OLED display that provides a quick overview of the RF signal, link quality, audio signal, battery status, frequency and encryption. Several screens provide easy access to additional information without the user having to search through complicated sub-menus. Messages of critical operating and error conditions are shown directly on the display.
  • DPA’s selection of mics for the drum kit is designed specifically to put the sound engineer in control of the sound. By starting with the clear, true sound of the entire kit, the engineer has the best starting point to shape the sound wanted for the situation. These mics guarantee a natural and precise sound reproduction of the entire kit. The specific mic placements prevent artefacts, bleed and other shadowing effects. The DDK4000 Drum Microphone Kit contains the following mics and accessories: Microphones 1 x 2012 Cardioid Microphone 2 x 2015 Wide Cardioid Microphone (Stereo Pair) 1 x 4055 Kick Drum Microphone 3 x 4099 Core Instrument Microphone, Extreme SPL Accessories 3 x MicroDot Cable (CM2218B00) 3 x Drum Microphone Clip (DC4099) 3 x Adapter for MicroDot to 3-pin XLR (DAD6001)
  • Clip for attaching a 4099 instrument microphone to thin-bodied and unusually shaped instruments. The design of the microphone clip includes a Velcro attachment strap to fit instruments of various sizes and diameters such as oboe, clarinet, bassoon, recorder and flute. The attachment strap tightens to fit the circumference of the instrument, like a wristwatch on your arm

  • The G4 In-Ear Monitoring Sets make your gig an extraordinary experience – not just for your audience, but also for you! Engineered for professional live sound: Rugged all-in-one wireless monitoring system for in-ear applications. Robust bodypack receiver and reliable in-ear monitoring IE 4 headphones delivering clarity along the whole frequency spectrum for daily use on stage Half-rack stereo transmitter in a full-metal housing with OLED display for full control Easy and flexible wireless synchronization between transmitter and receiver via infrared Compatible with Sennheiser WSM control software for flexible frequency allocation Up to 16 compatible channels Up to 42 MHz bandwidth with 1680 selectable frequencies, fully tunable in a stable UHF range Transmission Range: up to 100 meters / 300 feet High RF output power (up to 50 mW) depending on country regulations
  • Made from carbon fibre, the RØDE Boompole Pro weighs only 535gm (18oz) and, from a compact 810mm (2‘ 8”), extends to a full 3m (10’). Designed for use with professional shotgun microphones such as the RØDE NTG3 as well as the Blimp windshield system, the Boompole Pro joins RØDE’s popular boom pole range which now consists of five models ranging in size, weight, and construction material. Each of the five pole sections is comprised completely from carbon fibre making it incredible lightweight while maintaining high levels of strength. The sections are easily extendable with one hand thanks to an intuitive twist-lock mechanic. RØDE offers boom pole cable clips as an optional accessory, however the company’s new RØDELink wireless XLR adaptor allows users to record audio from a shotgun microphone on the end of the Boompole Pro without the hassle and possible handling noise of cables
  • The RØDE Blimp is a complete windshield and shock mounting accessory for the NTG1, NTG2, NTG3, NTG4 and NTG4+ microphones, as well as any third party shotgun microphone up to 325mm (12 ¾”) in length. Now featuring the Rycote® Lyre suspension system, the Blimp provides the ultimate in microphone suspension and isolation. Constructed from a single piece of hard-wearing thermoplastic, the Lyre provides superior acoustic suspension to traditional elastic solutions, and will never wear out, sag or snap. The Blimp’s handle has also been completely redesigned, reducing the product weight significantly, while increasing the ergonomics for handheld use. Housed inside the grip is a heavy-duty Mogami cable which splits via a junction box to a highly-flexible thin cable inside the Blimp, to minimise the transference of vibration to the microphone. With the lightweight design of the handle and suspension system the new Blimp design is over 25% lighter (550gm without microphone or DeadWombat fitted). The Blimp attaches to any standard boompole via 3/8" thread attachment at the base. The Universal Blimp Mount is available as an option to remove the handle when the Blimp is being used primarily on a boompole to reduce weight. The Dead Wombat windshield, caring brush and tail/patch cable are included.
  • The MKE 600 is the ideal video camera/camcorder microphone able to handle even demanding filmic challenges. Due to its high directivity, the MKE 600 picks up sounds coming from the direction in which the camera is pointing and effectively attenuates noise coming from the sides and rear. The switchable “Low Cut” filter additionally minimizes wind noise. Because some video cameras/camcorders do not provide phantom power, the MKE 600 can also be battery powered. A battery on/off switch prevents the battery from discharging prematurely; “Low Batt” is displayed. • Pronounced directivity • Maximal rejection of side noise • Switchable "Low Cut" filter minimizes wind noise • Phantom or battery powering • Battery switch with "Low Batt" indicator • Rugged all-metal housing • Very good suppression of structure-borne noise • Supplied with foam windshield and shock mount
  • The MV5 packs the clarity of almost a century of audio experience into a super-portable microphone. You get sound quality, squared. Singular simplicity: Plug-and-play is only part of the story. Though you’ll be set up in seconds, it’s also easy to select vocals, flat or instrument modes so you’re good to go when inspiration strikes. Globetrotting audio: Designed to travel with your computer or phone, the MV5 rests on its own or connects via a standard 3/4 inch (1.9 cm) mount to the included desktop stand. Easy, friendly control: The ShurePlus MOTIV audio app gives you the ability to record studio-quality audio — and so much more. Trim and share in multiple formats with a few quick taps.
  • The EK 6042 is a true diversity two channel receiver. It is designed to fit into all standard receiver slots on cameras. Its highly compatible to a wide range of Sennheiser wireless microphones be it analog or digital and can connect to virtually every Sennheiser wireless system including G3, 2000 series, 3000/5000 series and digital 9000. With the built-in web server, setup is easily managed using any browser including imports and exports of the entire configuration. The EK 6042 is SuperSlot™-compatible and works seamlessly with your existing equipment. Same for ARRI, Panasonic and Sony. The optional accessories like backpanel adapter and battery pack makes it possible to use the EK 6042 stand alone as well. The automatic configuration makes it possible to set up any microphone in less than 5 seconds.
    • 2 channel true diversity receiver
    • 184 MHz switching bandwidth
    • HDX, HiDyn+ AND Digital 9000 compatible
    • Camera adapters for Sony® and Panasonic® (Unislot)
    • SuperSlot™ compatible
    • Optional backpanel adapter & batterypack (Hot swappable)
    • Auto configuration & scene setup
  • The Sennheiser L 60 Charging Unit allows you to recharge two BA 60 or BA 61 rechargeable transmitter battery packs at once. The automatic charging process ensures that the battery packs cannot be overcharged, eliminating memory effect. The L 60 charger allows you to simultaneously charge two BA 60 or two BA 61 or one BA 60 and one BA 61. Up to four L 60 units can be daisy-chained and connected to a single NT 3-1 US power supply (available separately), to recharge up to eight battery packs at the same time.
  • The Expedition is a portable 2 channel, digital Broadcasters’ Phone with 7kHz HD Voice audio.  It is used for live news and sport reporting or talkback situations.  HD Voice is available on compatible 4G LTE and 3G UMTS networks.  Narrowband calls are also available on 2G GSM, 3G UMTS, and 4G LTE networks. A 2G GSM, 3G UMTS, and 4G LTE mobile phone with features specifically for broadcast. The HD Voice system allows 7kHz mobile calls on compatible mobile networks using 3G UMTS or 4G LTE networks. There are independent, duplicated controls for both inputs. The illuminated on-air button can be configured as latching, momentary or intelligent. There is a small gain control for setting input level. There are two x 6.35mm headphone sockets with a level adjust. Battery power is available from 6 x AA batteries. There is also an external DC input from 10 - 15V. The Expedition can be set to answer incoming calls automatically. An output compressor prevents any peak in the audio being sent onto the HD Voice network. HD Voice is very sensitive to peaks and the output compressor improves the quality of the audio received at the remote end.
  • The compact Y12 line array loudspeaker is designed for use in vertical columns. The 2-way passive design features two 8” drivers in a dipole arrangement and a centrally mounted 1.4” compression driver with a wave transformer. Sophisticated horn geometry combined with the advanced bass-reflex port design delivers full bandwidth capabilities with an extended LF output. These high performance line array modules offer 120° horizontal directivity controlled down to 500 Hz. The mechanical and acoustical design enables vertical arrays of up to twenty four loudspeakers with vertical splay angles from 0° to 14° with a 1° resolution. It can be used in columns of purely Y12 loudspeakers or combined with Y8 and/or Y-SUB cabinets. The loudspeaker cabinet is constructed from marine plywood and has an impact and weather protected PCP (Polyurea Cabinet Protection) finish. The front of the loudspeaker cabinet is protected by a rigid metal grill backed by an acoustically transparent foam. Each side panel incorporates a handle while two additional recessed grips are provided at the rear. Three point rigging hardware is integrated into the loudspeaker enclosure.

  • DANTE / MADI Converter

    • Design: 19 "/ 1U
    • 64 Channels
    • Included: Sample rate conversion, optical and coax MADI

    Ulteriori informazioni

    Amount Of Channels 64
    AD Conversion No
    DA Conversion No
    Max. Resolution 24 bit
    Max. sampling rate 192 kHz
    S/PDIF Connecor No
    AES/EBU Connector No
    ADAT No
    Word clock Yes
    Number of analog inputs 0
    Number of Analog Outputs 0
    Headphone connection No
  • Higher channel density with maximum signal reliability at the same time: Digital 6000 is intermodulation-free and assures through its equidistant frequency grid excellent spectral efficiency and the simplest frequency configuration– even in the toughest frequency environments where other systems already fail. Error correction and audio error masking recognize and fix problems long before they even become audible. When it comes to setup and the user interface, the EM 6000 stands out for clarity, relevance and short pathways. Digital 6000 can be seamlessly integrated into existing digital or analog infrastructures. The EM 6000 receiver has a digital AES-3 output with word clock inputs and outputs, high-quality transformer-balanced analog XLR and 6.3 mm jack outputs as well as a 6.3 mm headphone output. The Dante™ version with an Audinate Brooklyn ll card additionally offers two Amphenol RJ-45 connectors for integrating the receiver into a Dante™ network, for redundant networks or daisy chain cabling. Whether we’re talking about reducing information down to the really meaningful key values or smart menus on a high-contrast OLED display, every operating element is a result of practical experience and designed for practical use. All the vital parameters are summarized in one view. Important functions can be reached directly via home screens without long navigation paths. The auto-setup enables scanning and frequency distribution to all connected devices directly via the receiver; naturally Digital 6000 can also be monitored and configured via the Wireless System Manager (WSM). The EM 6000 is compatible with UHF Sennheiser antenna systems.

    Features

    • 19’’ 2-Channel receiver, 19 inch 1RU
    • Large 244 MHz switching bandwidth
    • Legendary Long Range mode (LR) with proprietary audio codec (SeDAC) from the masterpiece Digital 9000
    • True bit diversity utilizes both receiver paths, combines their information content to provide the best possible signal
    • Equidistant frequency grid for maximum channel density and simplest setup
    • 32 superior quality RF pre-selection filters for optimal suppression of interference signals at antenna input
    • Error correction and audio error masking
    • AES-256 encryption
    • Automatic frequency setup
    • Digital and transformer balanced analog outputs XLR, 6.3 mm jack, AES-3, EM 6000 Dante with Brooklyn II Card and Amphenol RJ-45
    • Integrated antenna splitter for cascading of up to 8 systems
    • one high-quality OLED display per channel
    • Link Quality Indicator (LQI)
    • Wireless Systems Manager (WSM) compatible
    • Compatible with standard Sennheiser UHF antennas
    • Compatible with Digital 9000 transmitters in Long Range mode
  • Now, the digital SK 6212 heralds a new era. This mini bodypack complements the Digital 6000 family, benchmark for challenging digital transmission technology in modern audio productions. Developed and designed hand in hand with key customers around the globe, the all-new entirely digital SK 6212 meets the highest requirements and so much more. For performers, stylists and directors, the SK 6212 is neither heavy nor conspicuous. It is as small as a matchbox and conveniently lightweight, has no sharp edges or corners and is discreet and easy to conceal. Furthermore, engineers appreciate exchangeable batteries and antennas, as well as direct operability and a dependable transmission. The SK 6212 operates intermodulation-free and utilizes an equidistant frequency grid that enables more efficient use of the constantly shrinking available frequency spectrum. And even when things are taking a bit longer, don’t worry… the 6212’s operating time lasts unbelievable 12 hours. The SK 6212 combines high expectations with the smallest possible design. It encapsulates hundreds of stories which we have heard from professionals in the world of theatres and music venues, large or small. Developed for today's shows and equipped for the challenges of the future.

    Features

    • Compact, ultra-small design with ergonomically optimized construction (63 x 47 x 20mm)
    • Designed for 12 hours of continuous operation
    • Made with ultra-light robust metal housing weighing only 112 grams
    • Intermodulation-free transmission – permits more channels even in very narrow frequency spaces thanks to equidistant frequency grid and simple setup
    • Superb sound and higher dynamic range thanks to Sennheiser Digital Audio Codec (SeDAC) and long-range mode, also found in the Digital 9000 series
    • Resistant to moisture and sweat
    • Two detachable clips (0°/90°) for secure fit in any position
    • Exchangeable antenna and battery
    • Can be used with a variety of lavalier microphones and headsets
  • The handheld transmitter SKM 6000 is intermodulation-free, which allows operation in an equidistant frequency grid. The transmission concept thereby permits maximum spectral efficiency even in the toughest frequency ranges. In short: more channels, maximum transmission performance at all times and hence outstanding signal stability. The SKM 6000 is compatible with Sennheiser and Neumann capsule heads and hence perfectly prepared for any stage, voice and requirement (evolution wireless, 2000, Digital 9000, Neumann KK 204 and KK 205). The special magnesium housing offers the perfect balance between low weight and live-compatible robustness. The lithium-ion battery pack BA 60 ensures up to 5.5 hours of operation; there is also the option of operation with batteries using the battery set B 60. The transmitter is also compatible with the EK 6042 and the EM 9046 in Long Range mode.

    Features

    • Three frequency variations (470-558 MHz, 550-638 MHz, 630-718 MHz)
    • Sennheiser standard capsule interface, compatible with microphone heads from evolution wireless G3, 2000, Digital 9000, Neumann KK 204 and KK 205 series
    • Highly effective intermodulation protection
    • AES 256 encryption and Digital 9000 encryption
    • Compatible with EK 6042 and EM 9046 in Long Range mode
    • Li-ion battery packs with 5.5 hours run time
    • Magnesium housing
  • The Yamaha CL series digital mixers represent a new level of refinement. They offer an advanced experience for simplicity of mixing, with in addition a purity and a capacity to shape the sound that will give every sound engineer unprecedented creative freedom. The CL series embodies the main standards of live sound in their most advanced and expressive form. The "virtual racks" available on the CL series consoles allows you to combine the signal processors needed for your work in a unique and easily accessible location, much like the traditional analog outboard racks. Efficiency and intuitiveness are essential. Yamaha's acclaimed Centralogic interface is the core of a revamped user interface that offers an unprecedented level of operational efficiency in the CL series, from visual feedback to the shape and tactile feel of faders and controls. The Yamaha Centralogic user interface has already demonstrated its value as the most user-friendly among the available digital operating environments, even for those engineers who were previously only at ease on analogue consoles..

  • The acclaimed CL series raised live digital mixing console performance to an unprecedented level of refinement with evolved sound quality, operability, and functionality, while maintaining the traditional values that have made Yamaha digital mixers industry standards. Core features and performance inherited directly from the CL series, including natural sound supported by sonically superb internal processing capabilities, operation that easily adapts to the demands of just about any working environment, and built-in Dante networking that facilitates flexible system configuration, have now been condensed and concentrated into the compact QL series digital mixing consoles. QL series consoles offer all-in-one mixing, processing, and routing capability for small to medium scale live sound, corporate speech events, installations, and much more.

  • The QL series mixers offer mixing, processing and routing functions for small and medium-sized live performances, corporate events, installations and much more.

    Pure and natural sound with a powerful internal processing for a wide and creative control

    The Yamaha sound starts with a faithful reproduction of the sound source. The QL series mixers are equipped with circuits and components that have been designed and selected with the utmost care, obtaining an audio with surprising purity, both in input and output.

    Refined control for smooth operation

    The ability to respond quickly and reliably to the many and changing needs is essential for effective support for live sound. The QL series mixers offer large touch-screen displays that, combined with the "touch and turn" potentiometer, provide a significantly quick and efficient control interface.

    Expandable All-in-One support for every application

    In addition to the wide availability of analog inputs and outputs, the QL series mixers are equipped with the same Dante audio network protocol available in CL mixers, which offers extensive connectivity. Also available is an innovative "Port to Port" feature that can direct each input port to each output port so that the QL mixer can function as a remote I / O device for any other QL or CL series mixer.
  • Features:

    • 19" Rackmount 5U
    • 32 Inputs and 16 outputs
    • 4x AES / EBU Out1-8
    • Dante network
    • Internal sampling frequency 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
    • External sampling frequency: 44.1 kHz: + 4,1667%, + 0.1%, -0.1%, -4.0% (± 200ppm) / 48 kHz: + 4,1667%, + 0.1%, -0.1%, -4.0% (± 200ppm) / 88.2 kHz: + 4,1667%, + 0.1%, -0.1%, -4.0% (± 200ppm) / 96 kHz: + 4,1667%, + 0.1%, -0.1%, -4.0%
    • Weight: 12.4 kg
  • Audio rental d&b audiotechnik Big Kit composed of: N.20 Q1 d & b audiotechnik N.4 Q7 d & b audiotechnik N.12 QSub d & b audiotechnik N.1 Yamaha M7CL mixer. Design and configuration assistance
  • The 2 RU four channel D20 amplifier is ideally suited to mobile and installation applications which require low to medium Sound Pressure Level (SPL) capabilities. The D20 features the same Digital Signal Processing (DSP) platform as the latest generation of d&b amplifiers, containing configurations for all d&b loudspeakers except the J-Series and the M2 monitor, plus a linear mode. The signal delay capability enables user definable settings of up to 10 s (= 3440 m/11286 ft), which can be applied independently to each channel. The same applies to the two 16-band equalizers, providing optional parametric, asymmetric, shelving or notch filtering. The D20 incorporates a colour TFT touchscreen, offering quick access to the menu structure, while the rotary encoder can be used for fine adjustment. The front panel and the integrated touchscreen are tilted up for easy operation when the amplifier is below eye level. The equal ratio of signal input to amplifier output channels increases application flexibility particularly for monitor, frontfill or effect channel use. The LoadMatch function integrated within the D20 amplifier electrically compensates for the properties of loudspeaker cable used. The D20 incorporates Class D amplifiers utilizing a power supply with active Power Factor Correction (PFC) suitable for mains voltages 100 V - 240 V, 50 - 60 Hz and maintains a stable output when used with weak or unstable mains supplies. An NL8 provides all outputs on a single connector for loudspeaker multicores. Dual channel mode is driven through four individual NL4 connectors, while Mix TOP/SUB and 2-Way Active mode output configurations for applicable d&b loudspeakers are available via two central NL4 connectors. etherCON and RJ 45 connectors enable access to the d&b Remote network through OCA/AES70 via Ethernet and through CAN-Bus respectively.

  • The 2 RU four channel D80 amplifier is a high power density amplifier, ideally suited for use in both mobile and installation environments. It contains configurations for all d&b loudspeakers and a linear mode. The signal delay capability enables user definable settings of up to 10 s (= 3440 m/11286 ft) to be applied independently to each channel. The same applies to the two 16-band equalizers, providing optional parametric, asymmetric, shelving or notch filtering. The D80 incorporates a colour TFT touchscreen, offering quick access to the menu structure, while the rotary encoder can be used for fine adjustment. The front panel and the integrated touchscreen of the D80 amplifier is tilted up for ease of operation when the amplifier is below eye level. The equal ratio of signal input to amplifier output channels increases the application flexibility particularly for monitor, frontfill or effect channel use. The LoadMatch function integrated within the D80 amplifier enables the electrical compensation of loudspeaker cable properties, without the need for an extra conductor. This results in an increased accuracy of audio reproduction over a bandwidth of up to 20 kHz, preserving the tonal balance when cable lengths of up to 70 m (230 ft) are used. The D80 incorporates Class D amplifiers utilizing a power supply with active Power Factor Correction (PFC) suitable for mains voltages 100 V/120 V/200 V/230 V, 50 - 60 Hz and maintains a stable output when used with weak or unstable mains supplies. An NL8 provides all outputs on a single connector, while individual outputs are optionally NL4 or EP5 connectors. RJ 45 and etherCON connectors enable access to the d&b Remote network via CAN-Bus and OCA/AES70 via Ethernet respectively.

  • The T10 is a passive 2-way loudspeaker housing two 6.5" drivers positioned in a dipolar arrangement and a 1.4" HF compression driver and a passive crossover network. The T10 can be used both as a line array and as a high directivity point source loudspeaker. The HF driver is fitted to a unique waveguide horn producing vertical line source directivity with a 90° horizontal pattern that is maintained down to approximately 600 Hz. An acoustic lens placed in front of the horn widens horizontal dispersion to 105°, rotation of the horn by 90° relative to this produces an accurate point source dispersion, transforming a vertically oriented T10 into a stand-alone full range loudspeaker with 90° horizontal and 35° vertical directivity pattern. The T10 cabinet is constructed from polyurethane integral hard foam, incorporates integrated line array rigging hardware and has an impact resistant finish. The front of the loudspeaker cabinet is protected by a rigid metal grill backed by an acoustically transparent foam, and two EP5 or NL4 connectors wired in parallel are mounted on the rear panel.

  • The compact, 2-way passive Y7P loudspeaker features two 8” drivers in a dipole arrangement with a 1.4” compression driver mounted onto a rotatable CD horn. Sophisticated horn geometry combined with the advanced bass-reflex port design delivers full bandwidth capabilities with an extended LF output. These point source, high performance cabinets offer 75° horizontal directivity controlled down to 500 Hz, matched with a vertical dispersion of 40°. The horn can be rotated by 90° to enable horizontal orientation. The Y7P provides a broad variety of deployment possibilities, especially when used as a stand-alone full range system, or combined with other elements from the Y-Series, either ground stacked or flown. The loudspeaker cabinet is constructed from marine plywood and has an impact and weather protected PCP (Polyurea Cabinet Protection) finish. The front of the loudspeaker cabinet is protected by a rigid metal grill backed by an acoustically transparent foam. The cabinet incorporates a pair of handles whilst M10 threaded inserts are provided for attaching d&b rigging hardware. Additionally, two further M10 sockets accept the 8mm load pin to expand the mounting options.

  • Shure Easyflex EZG and EZG-SE Series microphones are miniature gooseneck-mounted electret condenser microphones designed primarily for speech and vocal pickup. They can be mounted on lecterns, pulpits, or conference tables. All models include a preamplifier and are available with cardioid cartridges. EZG-SE Series microphones can be screwed onto a microphone stand or the supplied 5/8 inch, 27 threaded flange. They can be easily changed from side-exit to bottom-exit to conceal the cable.

    FEATURES

    • Single gooseneck section near microphone base for easy orientation of the microphone.
    • Tubular preamp body sized to fit many standard accessories.
    • Slide on windscreen
  • The versatile gooseneck provides stable and repeatable positioning. The mics can be easily unclipped and repositioned or moved to another instrument. The mounting system is designed to never blemish or scratch the finish of your instrument. The flexible design supports a wide variety of mounting and positioning possibilities.

  • The versatile gooseneck provides stable and repeatable positioning. The mics can be easily unclipped and repositioned or moved to another instrument. The mounting system is designed to never blemish or scratch the finish of your instrument. The flexible design supports a wide variety of mounting and positioning possibilities.

  • J-SUB is a bi-amplified 2-way bass-reflex subwoofer incorporating three 18 "long-excursion neodymium speakers, two of which are mounted on the front panel and one on the rear panel. which derives from this architecture avoids the unwanted projection of energy behind the system, which thus benefits from a considerable reduction of the reverberated field at the serious frequencies and therefore translates into an incomparable reproduction precision.The J-SUB systems can be used to complement the J8 and J12 systems in various combinations, either on the ground or suspended, either integrated into the column at the top of the J8 / J12 array, or in independent J-SUB columns. built in marine plywood covered with the exclusive PCP (Polyurea Cabinet Protection) treatment to protect against shocks and atmospheric agents.The front and back panels are protected by a rigid metal grid ca, while on each side panel there are four handles. Four 100mm wheels and an EP5 or NL8 connector complete the rear panel.

  • Rental Audio kit d & b audiotechnik composed by: N.6 d & b Q1 N.2 d & b Q7 No. 6 d & b QSub N.4 d & b D12 N.1 Yamaha LS9 mixer Design and configuration assistance
  • The compact Y8 line array loudspeaker is designed for use in vertical columns. The 2-way passive design features two 8” drivers in a dipole arrangement and a centrally mounted 1.4” compression driver with a wave transformer. Sophisticated horn geometry combined with the advanced bass-reflex port design delivers full bandwidth capabilities with an extended LF output. These high performance line array modules offer 80° horizontal directivity controlled down to 500 Hz. The mechanical and acoustical design enables vertical arrays of up to twenty four loudspeakers with vertical splay angles from 0° to 14° with a 1° resolution. It can be used in columns of purely Y8 loudspeakers or combined with Y12 and/or Y-SUB cabinets. The loudspeaker cabinet is constructed from marine plywood and has an impact and weather protected PCP (Polyurea Cabinet Protection) finish. The front of the loudspeaker cabinet is protected by a rigid metal grill backed by an acoustically transparent foam. Each side panel incorporates a handle while two additional recessed grips are provided at the rear. Three point rigging hardware is integrated into the loudspeaker enclosure.

  • d&b Q-sub

    30.00

    The Q-SUB is an actively driven low compression bass-reflex loudspeaker fitted with a high excursion 18" driver. d&b SenseDrive technology is available when powered by the D12 amplifier. The Q-SUB is mechanically compatible with the Q1 and Q7; ten sockets in the front grill and side panels for Q-Series rigging components permit use in various combinations, either flown or ground stacked. The Q-SUB cabinet is constructed from marine plywood with an impact resistant paint finish, a pair of handles, four heavy duty wheels and an M20 threaded flange in the top panel to accept a loudspeaker stand. The front of the loudspeaker cabinet is protected by a rigid metal grill covered with replaceable acoustically transparent foam and two EP5 or NL4 connectors wired in parallel are mounted on the rear panel. Two runners protect the bottom of the cabinet from scratching; these are located in correspondingly shaped recesses in the top panel to prevent movement when stacked. Fittings for securing an optional wooden lid are also provided.

  • d&b e12

    30.00

    The E12 and E12-D are high performance 2-way multipurpose loudspeakers, employing an integrated coaxial driver. The E12 and E12-D can be used for speech and music applications as stand-alone full range systems or incorporated into larger distributed sound reinforcement situations and, with the addition of an E15X or B4 subwoofer, can also easily reproduce high level music program. The multifaceted shape of the enclosure allows use either in an upright or horizontal orientation as well as deployment as a stage monitor. The E12 has an 80° x 50° dispersion pattern (h x v), while the E12-D has a wider 110° x 50° pattern. The horns in both loudspeakers are easily rotatable through 90° providing 50° x 80° or 50° x 110° dispersion patterns. The E12 and E12-D cabinet is constructed from polyurethane integral hard foam with an impact resistant paint finish incorporating handles and a hidden socket to accept loudspeaker stands. The loudspeaker cabinet is also available in Special Colour (SC) and Weather Resistant (WR) options. Both options are supplied with metal plates in the specified colour covering the handle recesses and loudspeaker stand socket.

  • The versatile magnet mount/gooseneck system provides stable and repeatable positioning.

    The mics can easily be positioned at different angles to provide a variety of sound nuances. The mounting system is designed to never blemish or scratch the finish of your instrument. The flexible design supports a wide variety of mounting and positioning possibilities.

    The mount can also be used with various instruments with magnetic surfaces.

  • This mic provides excellent off-axis rejection in high-SPL situations. It efficiently suppresses distant sound sources making it perfect for demanding live performance environments where background noise and feedback are concerns. In high-SPL events, or when feedback is a concern, this microphone will tackle these challenges with ease. The bass response is designed for optimal linearity at 2-3 cm (1 inch) from the sound source. This means that the bass roll-off will be relatively prominent at a greater distance - a paramount factor when it comes to rejection of background noise and in the fight to avoid feedback. The smooth and elegant design of the d:fine™ 4088 Directional Headset Microphone makes it the most invisible head-worn true cardioid microphone in the world. This microphone has a secure, dual-ear design that can be used for various performing talent applications. It has a small .64 cm (.25 in) diameter, which allows for discreet use. It only weighs 14 g (.5 oz) and is very comfortable when worn for long periods. The microphone can be mounted on the right or left side.

Title